Broadband-Hamnet™ Forum :: Hardware
Board Index Latest Posts Welcome Guest   [Register]  [Login]
 Subject :Problem with Nanostation.. 2014-10-26- 22:36:37 
sp2ong
Member
Joined: 2013-10-30- 10:57:25
Posts: 72
Location: 
Hi,

I have problem with my Nanostation M2. I have upload BBHN firmware and setup node after reboot
working very well. But after my manually changed via SSH session and reboot  I can not connect to my nanostation.
How to reset to default or other way connect to UBNT ???

I am looking similar way like for WR54
http://www.broadband-hamnet.org/documentation/71-using-safe-mode-to-reset-a-forgotten-password.html


73 Waldek SP2ONG
IP Logged
Last Edited On: 2014-10-26- 22:51:39 By sp2ong for the Reason
 Subject :Re:Problem with Nanostation.. 2014-10-26- 22:56:35 
KF5JIM
Future Astronaut
Joined: 2013-07-17- 12:13:36
Posts: 250
Location: Nederland

IMO, the easiest method would be to start over again. Instructions are found here (scroll to TFTP): http://ubnt.hsmm-mesh.org/products/BBHN/wiki/HowTo/FlashUbiquiti
IP Logged
My opinions and views expressed here are solely my own.
 Subject :Re:Problem with Nanostation.. 2014-10-26- 23:19:25 
sp2ong
Member
Joined: 2013-10-30- 10:57:25
Posts: 72
Location: 
Ok thanks, I will try. But one question more what kind firmware I need use in this situation SYSUPGRADE or FACTORY ?
IP Logged
 Subject :Re:Problem with Nanostation.. 2014-10-26- 23:22:55 
KF5JIM
Future Astronaut
Joined: 2013-07-17- 12:13:36
Posts: 250
Location: Nederland

Factory
IP Logged
My opinions and views expressed here are solely my own.
 Subject :Re:Problem with Nanostation.. 2014-10-26- 23:54:54 
sp2ong
Member
Joined: 2013-10-30- 10:57:25
Posts: 72
Location: 
Many thanks, all working and I can again resetup NS M2 73 Waldek sp2ong
IP Logged
 Subject :Re:Problem with Nanostation.. 2014-10-26- 23:57:32 
KF5JIM
Future Astronaut
Joined: 2013-07-17- 12:13:36
Posts: 250
Location: Nederland

No problem. I'm glad you were able to get it back up and running!
IP Logged
My opinions and views expressed here are solely my own.
 Subject :Re:Problem with Nanostation.. 2014-10-27- 03:31:44 
KG6JEI
Member
Joined: 2013-12-02- 19:52:05
Posts: 516
Location: 

Starting in version 3.0.0b02  on Ubiquiti this can be accomplished by just pressing and holding the reset button for 5 seconds (after the node has fully started)  it will reset the password for you and re-enable dhcp.  You can then go back to mesh setup and change the password and make any config changes you would like.  A 15 second press and hold would reset the node to "just flashed" status (resetting everything you did since you originally flashed the firmware image)
IP Logged
Note: Most posts submitted from iPhone
 Subject :Re:Problem with Nanostation.. 2014-10-27- 04:47:00 
KF5JIM
Future Astronaut
Joined: 2013-07-17- 12:13:36
Posts: 250
Location: Nederland
Correct. Not knowing what version and not wanting to dig into details it's always good to have more then one method at your disposal.
IP Logged
My opinions and views expressed here are solely my own.
Page # 


Powered by ccBoard


SPONSORED AD: