|
Your settings are same as mine. There arent any errors in your Output window. I dont know what else to say or try. Im posting my Nodes tab so you can see what it looks like with a connected mesh. The 172.30.1.2 address is my end of a GRE tunnel connecting the two 10.x.x.x nodes.
I have also post my Default.olsr file so you can see what is in it FWIW. 73; Bob KV4PC
#
# Configuration file for solsr.org - pre-0.5.6-r3
# automatically generated by olsrd-cnf parser v. 0.1.2
#
# Debug level(0-9)
# If set to 0 the daemon runs in the background
DebugLevel 0
# IP version to use (4 or 6)
IpVersion 4
# FIBMetric ("flat", "correct", or "approx")
FIBMetric "flat"
# HNA IPv4 routes
# syntax: netaddr/prefix
Hna4 {
}
# Should olsrd keep on running even if there are
# no interfaces available? This is a good idea
# for a PCMCIA/USB hotswap environment.
# "yes" OR "no"
AllowNoInt yes
# TOS(type of service) to use. Default is 16
TosValue 16
# Policy Routing Table to use. Default is 254
RtTable 254
# Policy Routing Table to use for the default Route. Default is 0 (Take the same table as specified by RtTable)
RtTableDefault 0
# The fixed willingness to use(0-7)
# If not set willingness will be calculated
# dynammically based on battery/power status
#Willingness 4
# Allow processes like the GUI front-end
# to connect to the daemon.
IpcConnect {
MaxConnections 1
Host 127.0.0.1
Net 10.0.0.0/8
Net 192.168.1.0/24
}
# Hysteresis adds more robustness to the
# link sensing.
# Used by default. 'yes' or 'no'
UseHysteresis no
# Hysteresis parameters
# Do not alter these unless you know
# what you are doing!
# Set to auto by default. Allowed
# values are floating point values
# in the interval 0,1
# THR_LOW must always be lower than
# THR_HIGH!!
#HystScaling 0.50
#HystThrHigh 0.80
#HystThrLow 0.30
# Polling rate in seconds(float).
# Auto uses default value 0.05 sec
Pollrate 0.05
# Interval to poll network interfaces for configuration
# changes. Defaults to 2.5 seconds
NicChgsPollInt 2.50
# TC redundancy
# Specifies how much neighbor info should
# be sent in TC messages
# Possible values are:
# 0 - only send MPR selectors
# 1 - send MPR selectors and MPRs
# 2 - send all neighbors
#
# defaults to 0
TcRedundancy 2
# MPR coverage
# Specifies how many MPRs a node should
# try select to reach every 2 hop neighbor
# Can be set to any integer >0
# defaults to 1
MprCoverage 7
# Link quality level
# 0 = do not use link quality
# 1 = use link quality for MPR selection
# 2 = use link quality for MPR selection and routing
LinkQualityLevel 2
# Fish Eye algorithm
# 0 = do not use fish eye
# 1 = use fish eye
LinkQualityFishEye 1
# Link quality algorithm (if LinkQualityLevel > 0)
# etx_fpm (hello loss, fixed point math)
# etx_float (hello loss, floating point)
# etx_ff (packet loss for freifunk compat)
LinkQualityAlgorithm "etx_ff"
# Link quality aging factor
LinkQualityAging 0.100000
# NAT threshold
NatThreshold 1.000000
# Clear screen when printing debug output?
ClearScreen no
# Olsrd plugins to load
# This must be the absolute path to the file
# or the loader will use the following scheme:
# - Try the paths in the LD_LIBRARY_PATH
# environment variable.
# - The list of libraries cached in /etc/ld.so.cache
# - /lib, followed by /usr/lib
LoadPlugin "olsrd_txtinfo.dll" {
PlParam "Accept" "127.0.0.1"
}
LoadPlugin "olsrd_dot_draw.dll" {
PlParam "Accept" "127.0.0.1"
}
LoadPlugin "olsrd_httpinfo.dll" {
PlParam "port" "8080"
PlParam "Host" "127.0.0.1"
PlParam "Net" "10.0.0.0 255.0.0.0"
PlParam "Net" "192.168.0.0 255.255.0.0"
}
# Interfaces
# Multiple interfaces with the same configuration
# can shar the same config block. Just list the
# interfaces(e.g. Interface "eth0" "eth2"
Interface "IF35" {
# IPv4 broadcast address to use. The
# one usefull example would be 255.255.255.255
# If not defined the broadcastaddress
# every card is configured with is used
#Ip4Broadcast 255.255.255.255
# IPv6 address scope to use.
# Must be 'site-local' or 'global'
Ip6AddrType global
# IPv6 multicast address to use when
# using site-local addresses.
# If not defined, ff05::15 is used
Ip6MulticastSite ff05::15
# IPv6 multicast address to use when
# using global addresses
# If not defined, ff0e::1 is used
Ip6MulticastGlobal ff0e::1
# Olsrd can autodetect changes in
# interface configurations. Enabled by default
# turn off to save CPU.
AutoDetectChanges: yes
# Emission and validity intervals.
# If not defined, RFC proposed values will
# in most cases be used.
HelloInterval 5.00
HelloValidityTime 125.00
TcInterval 3.00
TcValidityTime 375.00
MidInterval 25.00
MidValidityTime 375.00
HnaInterval 25.00
HnaValidityTime 375.00
#LinkQualityMult default 1.0
# When multiple links exist between hosts
# the weight of interface is used to determine
# the link to use. Normally the weight is
# automatically calculated by olsrd based
# on the characteristics of the interface,
# but here you can specify a fixed value.
# Olsrd will choose links with the lowest value.
# Note:
# Interface weight is used only when LinkQualityLevel is 0.
# For any other value of LinkQualityLevel, the interface ETX
# value is used instead.
#Weight 0
}
# END AUTOGENERATED CONFIG |
