Just upgraded to 1.1.0 on Wrt54GS v1.  Used root & hsmm

All is well!

73

Doug

A bit moren details please on the layout,  

Ubiquiti or Linksys ? 

Mode (Direct or NAT) 

saying the advertisement does to show up even on the local node it's set on correct ?  You can get (from a remote node) to the node that has the advertised service by name  but can't get to a name that's reserved on that node for a local system ?

Hey, thanks for the reply and apologies for the delayed reply on my part. I've been just swamped lately and this new gizmo isn't quite my highest priority.

I was connecting LAN to LAN ports before. When I switched to the WAN port on the Mesh node, it did indeed become visible through my WiFi router. And as soon as I brought up the local node's status page, it showed connection to another mesh node, parked out in the garage. But as you indicated, if I try to daisy-chain my way on over to that distant node, it can't be reached.

And I think I understand why, now. Thanks again for the reply.

Benton 7jul14

--

KF7QLP

benton@siletzbay.com

Yep, checksums match now.

You're really busy today, Jim.  :-)

Mark K5LXP

Albuquerque, NM

Mark,

found the problem... copy/paste got away from me.

Clear the cache and refresh. Should be good now

Yes, I have 7 nodes upgraded to 1.1.0 and all appear to be working normally..

amazing what little bitty details can make happen, or NOT..

See why we broke away 200+ years ago :-)

Is there no part of the 2.4 band y'all can use?

Let us know specifics, as many more will want to know

73

FYI-

The MD5 checksum for the new 1.1.0 firmware doesn't match for this file:

<http://www.broadband-hamnet.org/download/firmware/link/bbhn-1.1.0-wrtsl54gs-2.4-squashfs.bin>

Multiple download attempts yields the same result.  All other files checksum OK.

Mark K5LXP

Albuquerque, NM

Good Afternoon Everyone,

So I went ahead and updated some of my nodes to the new 1.1 firmware.  I seem to have hit a snag, or at least I think I have.  After I set everything backup as far as the advertised services on the node that is attached to a server and rebooted the node, I find that when I goto the Mesh Status page that those services are not being advertised on the mesh status page.  Additionally, the DNS resolution for the name of the server (as set by the static IP address) doesn't seem to be working either.  I am able to get to other upgraded nodes by their names but nothing that is attached to them.  Suggestions?  Thoughts?  What did I do wrong/break?

Thanks in advance,

73,

Travis W9HDG

I managed to find out some information in relation to this. A portion of the 13cm/2.3GHz band in the UK is now no longer available.

Information is available here:

http://rsgb.org/main/operating/band-plans/microwaves/spectrum-release/

The part which is no longer available included the band that is needed for the mesh. This frequency has the allocation for 1000kHz bandwidth that the high speeds require.

http://www.md0mdi.com/rsgb-band-plan-13cm/

I have looked into the 6cm/5.7GHz band, but I have been unable to find any information that shows how much bandwidth is allocated for each frequency within the band.

Jack.

My Bad... The file was there, the index page missed it.

I have fixed it, and you may need to clear your browser cache to pick up the change.

73

IS there a bin file for the wrtsl54gs and the new v1.1.0  ?  Currently this is ONLY available as the now-older v1.0.0 file.

TIA for the reply/file es vy 73 de;

Bob, w9ya

We are aware of the situation and are working to correct that.

We should have it fixed sometime today.

KTF

I have a Bullet M2 with 1.0.1 loaded.  The 1.1.0 upgrade does not appear in the "Download firmware" list after hitting refresh.

Not a huge deal, because I can download it to my Mac, and upload it, but, wanted to mention the isssue.

Thx,

K5DLQ - Darryl

I'm situated on the east side of Waynesboro. If facilities were available at... I dunno... maybe Carter Mountain and Bear Den or Afton mountain, could both sides of Afton be linked with gain antennas and no amps?